HIGH PERFORMANCE
STAINLESS STEEL BRAKE LINE SETS |
Features:
-
Strong braking power
- Heavywall Teflon liner eliminates spongy feel
- Aircraft quality stainless steel components
- Quality checked ! Each hose pressure tested to 4000 PSI
|
LIFTED TRUCKS
Since 1980 NWOR's high performance stainless steel brake line sets have been a "must have" item on lifted trucks. Lifted vehicles tend to stretch stock length brake hoses to their limit! NWOR hose sets are longer than stock hoses, ready to install on your Toyota 4x4. These are the same quality brake lines used on leading off-road race vehicles. Kit includes 2 front and 1 rear hose ready to install.
| Lifted Truck Brake Line Sets |
| 3"-4" Lift '79-'85 |
N76500 |
| 3"-4" Lift '86-'95 |
N76510 |
| 5"-7" Lift '79-'04 |
N76550 |
| 2"-4" Lift '96-'04 (Tacoma) |
N76600 |
| 2"-4" Lift '96-'04 (4R) |
N76610 |
|
| |
|
HYPERFIRM® HIGH PERFORMANCE
STAINLESS STEEL BRAKE LINE SETS |
NON-LIFTED TRUCKS
Hyperfirm® stainless steel brake line kits are designed for vehicles with standard height suspension. The kit features a patented spring assist whip dampener that surpasses stringent Department of Transportation (DOT) testing for brake lines. Drivers can expect a firmer pedal feel and reduced or eliminated pulsing common to ABS brake systems.
|
| Hyperform® Brake Line Sets |
| DOT Hose Set ('79-'93) Truck |
N76450 |
| DOT Hose Set ('84-'85) Truck |
N76455 |
| DOT Hose Set ('86-'88) Truck |
N76460 |
| DOT Hose Set ('89-'95) Truck |
N76465 |
| DOT Hose Set ('95-'97) Tacoma |
N76470 |
|
| |
|
| ULTRA HIGH PERFORMANCE BRAKE PADS |
Now Available:
Extreme-Duty
Police Type Pad Sets
Add EXD to Part #
See Model Numbers To Right |
| Performance Pad |
N09101 |
| Extreme Duty Pad |
N09101-EXD |
|
Factory Toyota truck brakes cannot compensate for heavier, and larger, aftermarket tires and wheels. Those brakes fade easily and panic stops are useless. NWOR is proud to offer the finest Toyota 4x4 semi-metallic brake pads on the market. Semi-metallic brakes exhibit no fading under harsh conditions. The hotter the metallic brakes get the better the truck stops. This is the opposite of stock linings. Please state year and model. |
| |
|
| BRAKE EQUALIZER BRACKET |
| When the rear of the Toyota has been raised, without correcting the length of the proportioning valve linkage, rear braking is decreased and the front disk pads wear 3 times faster than normal. This bracket has been furnished with all '79-'95 NWOR rear springs and will correct the problem. |
| Equalizer Bracket (2"-4" lift) |
N09330 |
|
| |
|
 SOLO BLEEDS |
 Brake bleeding has always been an inconvenient and messy job. Commercial shops typically use an expensive pressure bleeder — which, unless used properly, can introduce air bubbles into the system through cavitation. Vacuum bleeders are less expensive but can also introduce air into the system.
The time honored manual method (still universally used in racing) requires two people: one to pump the pedal, and another to open and close each bleed screw in sequence. Again, proper procedure and coordination are required to prevent air inclusion.
Earl’s SOLO-BLEED™ bleeder screws solve both problems. A direct replacement for the original equipment bleeders, SOLO-BLEED™ allows one person to safely bleed brakes without a mess and with no chance of air inclusion. Please state year and model.
| Solo Bleeds (Set of 2) |
N09000 |
|
