|
PAGE
ONE |
PAGE TWO
FACTORY
REPLACEMENT
SWAY BAR BUSHING KITS
|
|
|
| '89-'95 Part #80018 |
'79-'85 Part #80015 |
Truck
and '84-'89 4Runner
| Sway
Bar Bushing Set '79-'85 |
N80015 |
| Sway
Bar Bushing Set '86-'88 |
N80016 |
| Sway
Bar Bushing Set '89-'95 |
N80018 |
Tacoma
'96-'04
| Sway
Bar Bushing Set 26mm |
N80029 |
| Sway
Bar Bushing Set 27mm |
N80030 |
Tacoma
'02-'04
| Sway
Bar Bushing Set 26mm |
N80032 |
| Sway
Bar Bushing Set 27mm |
N80033 |
4Runner
'90-'95
| Sway
Bar Bushing Set (Front) |
N80025 |
| Sway
Bar Bushing Set (Rear) |
N80026 |
4Runner
'96-'04
| Sway
Bar Bushing Set (Front) |
N80034 |
URETHANE
BODY MOUNT SET
These urethane,
Toyota replacement body mount sets have been designed to replace
the factory rubber components which break down rapidly from
oil, grease, and hard off-road use. Our urethane body mounts
will provide a superior ride that is
quieter than factory due to the cushioning and sound
insulation values of quality urethane. The body mount set
is a must for trucks equipped with body
lift kits which cause extra stress on the rubber mounts.
The kit includes both cab and radiator core support mounts
and is furnished with all necessary hardware and machined
sleeves.
|
Body Mount Set '79-'88 (Truck) |
N80040 |
Body Mount Set '84-'89 (4R) |
N80042 |
Body Mount Set '89-'95 (Truck) |
N80044 |
Body Mount Set '96-'01 (Tacoma) |
N80046 |
Body Mount Set '01-'04 (Tacoma) |
N80047 |
Body Mount Set '93-'98 (T-100) |
N80048 |
STEERING
RACK URETHANE BUSHINGS
| The rack & pinion steering system on the 1996-2003 Tacomas and 4Runners is manufactured as an entire assembly and then bolted to the chassis using rubber bushings. The rubber wears rapidly from stress caused by oversize tires and normal wear. NWOR's urethane replacement set will improve your truck's steering response and tighten up that loose feeling. The urethane bushing set with machined sleeves is a quick install. |
Steering Rack Bushings '95-'00 |
N80078-(E) |
Steering Rack Bushings '01-'04 |
N80078-(L) |
IFS
CONTROL ARM SET
NWOR control arm bushings are designed to be full floating and non-binding throughout the full range of suspension travel. This becomes especially important when ride height has been altered or when greater suspension travel is required for off-road use. Due to ease of accessibility, we highly recommend using our heavy duty N69510 grease (see page 61) during installation. Set includes both sides' upper and lower bushings.
IFS Control Arm Set '86-'88 |
N80017 |
IFS Control Arm Set '89-'95 |
N80019 |
IFS Control Arm Set '96-'04 Tacoma |
N80023 |
|
2-1/2" FRONT
BUMP STOPS
FINALLY BACK IN STOCK!
2-1/2" Bump Stop (pr.)
|
N80060 |
|
|
NWOR'S
2 1/2" bump stop kit is highly recommended
for all '1979 - '85 Toyotas with 2" to 7" front
replacement springs. These
will stop the spring from OVER-EXTENSION which
results in spring failure. Kit includes heavy
duty offset replacement
brackets to ensure proper alignment of bump stop to
frame.
|
|
2-1/2" & 4" REAR
BUMP STOPS
2-1/2" Bump
Stop (pr.) |
N80062 |
4" Bump
Stop (pr.) |
N80064 |
|
NWOR's urethane bump stops mount over the rear axle and provide a progressive cushion when your Toyota bottoms out its rear suspension. These bump stops reduce stress on both the driver and the Toyota's drivetrain and suspension components. A must for hard off-road use. |
|
